My 2019 build today had a dodgy micro USB connector to wiring stub so I connected the Pi to the powered USB hub and the 3A buck converter [3 pots and a red board type] set at 5.3V (no load) did really well. Lime and all accessories were there too. No low voltage alerts after two transmit cycles. Is that an acceptable way to go?
My RPi model 1 was powered off a USB hub which lives in my Portsdown accessory box today. It was the recommended thing to do in the Beginning of Pi.
I saw this short connector https://thepihut.com/products/short-mic ... pi-display which would suit as the Pi sits over the hub in order to get a smaller package size.
Ground connection PP5 is too close to PP2. PP3 is easier to access. My Pi 3B+ powered up fine with 5.2V across PP2 & PP3. So careful wire soldering is on.
- Pi 3B+ power points.
- PhotoPictureResizer_190210_122355378-1008x756.jpg (209.3 KiB) Viewed 210 times
M0YDH wrote: ↑Sat Feb 09, 2019 11:47 pmHello Ken
I've been in your shoes with Portsdown.
Many of us have bought 2 Waveshare screens. The safest bet is to get it cased up in a printed plastic surround [e.g. from radiogareth] ASAP and use a ribbon cable connector.
Colin G4KLB's Portsdown was very influential and I copied it too. It's a great piece of work and won a prize at CAT17 IIRC. Colin has a big shack with lots of desk space so can plug USB items in to the Pi without mounting them in the case. The connections on the side of the case have become a nuisance for me in my rack system. A lot of the precious space on the rear panel is taken up with buck converters. So later features like composite video/audio out and e.g. signal generator port don't feature. The band select board shown has no outputs. My first Portsdown has an accessory box for the powered USB hub to house the gear that didn't fit in. There's a further unit to do Rx/Tx changeover and amp selection.
You've found the interconnect diagram. I found it baffling at first! I looked at it today and its seems quite elegant. (Portsdown 2019 thatI put together today only uses 3 main groups from the breakout board - 2 if no attenuator - you're doing the full fat version
The Pi needs a net 5.1 V across it from its own regulator - you are correct. A buck converter or LM338T home brew per the Texas Instruments data sheet do well. A small LCD voltmeter is handy as part of the set up so you can tweak it. Ripple filters can be added - my arrangements came from LM2756 data sheet. G4KLB's has these after each buck converter.
The ADF4351 uses one of the buck converters as it seems to need 6-8 VDC - see Wiki. I've soldered a wire to the back of the power connector housing. Only LE, CLK, DAT and GND come from the Portsdown.
I have a 7805 regulator for the LO filter (and I think FM board too) 5V. It could take supply from the same regulator as the Pi.
The 3.3V line from the breakout board does 4-Band decode and the RF switch.
The FM board is supplied from 12-13.8V supply and has on board voltage regulation. In any event do what G8GKQ says!
A Stripmaster and a crimp tool for Molex KK connectors will help enormously.
I hope this helps.
Thanks for that info. very useful. By the way my touch screen got damaged whilst i was messing with a screen ribbon extender. A frend made me a bezel on his 3d printer. I also have the molex connectors all wired but was waiting for the dupont type Plug which came yesteday for the ADF435x . Fiddly things but that end of the 4 wires LE, CLK, DAT and GND is now done too.
Like you I have this morning soldered wires direct to underside of the power socket. I do have a plug with cable for it but silly me mounted the ADF board too close to the BUCKS to get the plug in !
Of all things im building into a Ferrero Rocher see through plastic box ( I ate only the last one and "she" ate the rest ). I only bought them for her at Cristmas so I could have the box !
Yes I have printed out that wiring layout / interconnect and yes I agree its quite neat.
Its the test bed and if it all works I have a very nice metal case I will build into that matches my 2 lots of Analogue gear 1 for 23cm and one for 13cm.
I dont have ALL the boards YET but ive all the bits for the 23cm 1st test.
So, Once ive connected up the 3 bucks ( after setting the voltages ) it will be test time.
The ribbon cable ( from piHUT for the screen doesnt fit nice on the pins on GPIO board and the plastic shell is too wide at the ends) I'm intending to cut off the not used pins on GPIO as the cable should fit better. It was when fiddling with this ribbon that I duffed the touch screen. However its only the touch part that gone AWOL. the actual display is fine.
Im just about to check / determine the pinouts on USB PLUG so I can use a cut off USB lead for connecting the PI to one of the Bucks. If I remember from my time replacing USB sockets on TomTom sat/navs I do already know BUT i need to be sure of course.
Once again thanks for your help. Ken G8VDP
This post is now , perhaps on wrong thread but I thought I'd put it here just to let you know your help above has got me to this point.
Thanks all Ken
I "think" I've tried that but I'll try it again.
I have several satellite receivers Comag etc + a posh rack mount one. I've yet to try those.
First time I tried the Satlink was on GB3YT it took a while to get it to see it. Having gone within 500 yards of it.
Next time was on Anglesey but by then I'd learnt how to drive it. Or just got lucky !
Also my very good friend Gary M1EGI has a MiniTiouner that he can bring down. He's not old like me , he's young & keen.
I must admit, my brain still works in analogue and I'm very slow to understand FEC Bouquets PIDs etc.
I also got confused when the filter modulator board got mentioned further up this thread calling it the FM board in an earlier reply . then found out it wasn't (the FM as in SSB AM FM ) but it meant
"filter modulator". Duh !
Many thanks Ken
This is screenshot of video I took yesterday. Don't try tapping the triangle