GB3UD

Ideas, technical topics, help and discussion for ATV enthusiasts
Forum rules
This forum is run by the BATC (British Amateur Television Club), it is service made freely available to all interested parties, please do not abuse this privilege.

Thank you
Post Reply
Paul_01
Posts: 12
Joined: Mon Mar 08, 2021 12:36 pm

GB3UD

Post by Paul_01 » Thu Nov 28, 2024 5:46 pm

Hi
I am located about 30 to 40 miles west of the GB3UD repeater and I would be grateful if someone could provide me with the current status,
eg operational times, parameters etc. as I would like to access GB3UD.

Thanks
Paul m1bkl

Basil
Posts: 347
Joined: Tue Sep 10, 2013 7:28 pm

Re: GB3UD

Post by Basil » Thu Nov 28, 2024 6:03 pm

From the BATC streamer site:


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

GB3UD is an ATV repeater situated at Mow Cop, Staffordshire IO83VC

The repeater's receivers are as follows; For DVB-S Digital Input a Cisco PowerView 9850 with ASI Digital Output and for Analogue Input an EchoStar LT8700 both with an Input Frequency of 1249 Mhz and a Digital MPEG2 Output at 1318.5 Mhz

Settings for Digital Transmissions through the repeater; Input Frequency 1249Mhz, Symbol Rate 4.167 MS/s, FEC set to 1/2, PID's set to VIDEO 162, PMT 32 and AUDIO 88

NOTE: Both the FM Analogue Input and Digital Input are always Output as a Digital MPEG2 Output with the above Digital settings at 1318.5 Mhz with MPEG2 4.167MS/s FEC 1/2 Output Encoding.

The GB3UD stream is fed to the BATC by Simon G4OUK from his QTH in Cheshire



See you on the repeater.

Talkback 144.750

Activity night every Wednesday

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

I will be curious as to how you get on as I am about seven or so miles south of you. However, I rarely see any activity on GB3UD, unfortunately.
Best regards,

Chris, 2E0ILY in rural Shropshire.

Paul_01
Posts: 12
Joined: Mon Mar 08, 2021 12:36 pm

Re: GB3UD

Post by Paul_01 » Fri Nov 29, 2024 10:44 am

Hi

Thank you for the information.
I will start by trying to monitor your transmissions next Wednesday, what time ?
Unfortunately I only have a 2m handheld so I may not hear the talk back.
I can however easily access the 23 repeater GB3SE and I assume you are not to far away - for beam alignment.

Thanks again
Paul m1bkl

Paul_01
Posts: 12
Joined: Mon Mar 08, 2021 12:36 pm

Re: GB3UD

Post by Paul_01 » Fri Nov 29, 2024 10:49 am

Hi Chris

Yes we are quite close - do you have a 23cm setup?
I have seen you on QO-100, but not recently as unfortunately my system is off air should be back at the end of the year.

Paul m1bkl

Basil
Posts: 347
Joined: Tue Sep 10, 2013 7:28 pm

Re: GB3UD

Post by Basil » Fri Nov 29, 2024 12:15 pm

No, I have a mast I could put a Yagi on but am loathe to buy anything until I know I am likely to be able to access this repeater. Plus 23cms seems a bit in doubt these days.... I'll let you be the Guinea pig Paul :) You can monitor the stream from GB3UD here, I haven't seen any activity at all in months.

https://batc.org.uk/live/gb3ud
Best regards,

Chris, 2E0ILY in rural Shropshire.

Paul_01
Posts: 12
Joined: Mon Mar 08, 2021 12:36 pm

Re: GB3UD

Post by Paul_01 » Fri Nov 29, 2024 2:42 pm

OK Thanks I will let you know how I get on.

I also have most of the equipment I need for 70cm, if you use that band?

Paul m1bkl

Post Reply

Return to “General ATV Discussion”