Hardware for EsHailSat2

Latest News and Discussion about the use of the DATV transponder on Es'hailsat 2
Post Reply
oe7dbh
Posts: 55
Joined: Fri Feb 15, 2013 2:03 am

Hardware for EsHailSat2

Post by oe7dbh » Fri Aug 05, 2016 4:03 am

OE Forum page about it: http://www.oe7forum.at/viewtopic.php?f=42&t=468#p1663

Potential hardware components for Es'HailSat or other terestrial use.

For the satellite reception.... PLL LNB
DSCN8878x.jpg
DSCN8878x.jpg (190.18 KiB) Viewed 3768 times
more information here: http://www.oe7forum.at/viewtopic.php?f= ... =135#p1519




To send, UP Converter:
1.jpg
1.jpg (938.38 KiB) Viewed 3768 times

for DVB , CW and SSB signals....
3.jpg
3.jpg (785.9 KiB) Viewed 3768 times
and with DVB signals... http://www.oe7forum.at/viewtopic.php?f= ... =375#p2050

more information here: http://www.oe7forum.at/viewtopic.php?f= ... =150#p2045
Hopefully no more start delays ;)

vy 73 de Darko OE7DBH
oe7dbh@tirol.com


been translated into English with google
Last edited by oe7dbh on Sun Dec 25, 2016 12:44 am, edited 2 times in total.

oe7dbh
Posts: 55
Joined: Fri Feb 15, 2013 2:03 am

Re: Hardware for EsHailSat2

Post by oe7dbh » Sat Sep 24, 2016 9:13 pm

...another one LNC for receiving :
Output1 or Port1 for DVB-S
Output2 or Port2 for SSB - CW on 70cm Band
Twin20LNC.jpg
Twin20LNC.jpg (289.29 KiB) Viewed 3531 times
88,00 Euro kit including: LNB , T bias , Adapter F male to BNC female

oe7dbh
Posts: 55
Joined: Fri Feb 15, 2013 2:03 am

Re: Hardware for EsHailSat2

Post by oe7dbh » Wed Mar 22, 2017 1:38 am

http://www.ebay.com/itm/BU-500-13cm-Up- ... 33ca9b00b4
s-l1600.jpg
s-l1600.jpg (197.9 KiB) Viewed 2698 times

9a6rzn
Posts: 2
Joined: Sat Jun 09, 2018 10:12 pm

Re: Hardware for EsHailSat2

Post by 9a6rzn » Sat Jun 09, 2018 10:24 pm

HiDes UPconverter made special for EsHail2 HamRadio Transponder...
DSCN0461x.jpg
DSCN0461x.jpg (541.9 KiB) Viewed 403 times
Block.jpg
Block.jpg (67.23 KiB) Viewed 398 times
Block2.jpg
Block2.jpg (164.19 KiB) Viewed 398 times
BU500 Ver.2 and Ver.3 "ready for use" in the housing comes with measurement protocol.

G1BVI
Posts: 48
Joined: Wed Aug 02, 2017 7:32 am

Re: Hardware for EsHailSat2

Post by G1BVI » Mon Jun 11, 2018 12:37 pm

Input Drive Level?

On the image showing the DUT hooked into an analyser the drive level is shown as 0.5mW which is about -3dBm.

However the drive on V1 and V2 is -10dBm which is 0.1mW and the drive on V3 is +10dBm which is 10mW.

Was the original DUT being over driven or under driven I wonder.

The output of a FT818 is about 6W call it 38 dBm. (We all forget to switch the power down at some point!)

a 30dB attenuator will therefore be required to drive the v 3 unit .

I think my Maths is correct.

For a pi circuit
this gives values of 53 ohms and 800 ohms.

The 53 ohm input resistor would need to made up of several to get to this value and be able to sink the power of 6W.

I tried lowering the value to 50 ohms as these are easy to purchase at higher wattages but the return loss gets worse.

A quick google search however found some cheap ready made attenuators.
Roll on pay day :-)

Roll on launch date !???????

73

Nick
G1BVI

9a6rzn
Posts: 2
Joined: Sat Jun 09, 2018 10:12 pm

Re: Hardware for EsHailSat2

Post by 9a6rzn » Mon Jun 11, 2018 9:15 pm

On the image showing the DUT hooked into an analyser the drive level is shown as 0.5mW which is about -3dBm.
However the drive on V1 and V2 is -10dBm which is 0.1mW and the drive on V3 is +10dBm which is 10mW.
Was the original DUT being over driven or under driven I wonder.


Picture above shows the inner one of the first prototypes, with more than allowed input Levels ( without Input attenuator and 0,5mW Signal ). Nevertheless clean output signal.

The output of a FT818 is about 6W call it 38 dBm. (We all forget to switch the power down at some point!)

We have a head on our shoulders to think about that ;)

a 30dB attenuator will therefore be required to drive the v 3 unit for SSB-CWYES
For digital Television: attenuator value depends on TX output signal Level , there are two versions UPconverter available :)

Post Reply

Return to “Es’hail-2 - DATV Transponder”