Motorola MHW2723
Forum rules
This forum is run by the BATC (British Amateur Television Club), it is service made freely available to all interested parties, please do not abuse this privilege.
Thank you
This forum is run by the BATC (British Amateur Television Club), it is service made freely available to all interested parties, please do not abuse this privilege.
Thank you
Motorola MHW2723
Has anyone built up an amp for DATV using the Motorola MHW2723 that could pass on either a board layout or some constructional tips.
Many thanks Ian.
Many thanks Ian.
Re: Motorola MHW2723
There's a document here in French:
http://f1chf.free.fr/DIGILITE/Ampli%205 ... 0F1DJO.PDF
If I've understood the French correctly, pcbs are available from CIMKO for €3 + €2 postage. Google says the description means 'epoxy with printed chokes'.
http://fr.groups.yahoo.com/group/ListeATV/message/7849
Email: cimko at free.fr
Perhaps if several people were interested, it would be worth ordering a few to save on postage from France.
Brian
http://f1chf.free.fr/DIGILITE/Ampli%205 ... 0F1DJO.PDF
If I've understood the French correctly, pcbs are available from CIMKO for €3 + €2 postage. Google says the description means 'epoxy with printed chokes'.
http://fr.groups.yahoo.com/group/ListeATV/message/7849
Email: cimko at free.fr
Perhaps if several people were interested, it would be worth ordering a few to save on postage from France.
Brian
Re: Motorola MHW2723
Thanks for the info - would certainly be interested in a couple myself having purchased a few of the devices on eBay. Hopefully it will get some useful power out of the XZD station.
Cheers Ian.
Cheers Ian.
Re: Motorola MHW2723
I've emailed Cimko and asked how much it would cost to send a number of them over here.
Brian
Brian
Re: Motorola MHW2723
Just out of interest the French page shows two pcb layouts - a simple-looking one and then another much more complicated. Presumably the complicated one has the inductors etched on the pcb - or am I wrong?
Re: Motorola MHW2723
That's the impression I got. The prototype pcb had wired inductors and the final one has them printed.
No reply from Cimko yet.
Brian
No reply from Cimko yet.
Brian
Re: Motorola MHW2723
I am interested in one of these boards too as I did purchase one of the MHW2723 modules and had not tried it yet. €3 + €2 = €5 in my book and Iound €5 note in my 'junk box' recently. Wonder if a Greek €5 note is still worth €5 these days ![Smile :-)](./images/smilies/icon_e_smile.gif)
It will be interesting to see how much power it will run with sufficient linearity for DATV.
Dick G4BBH
![Smile :-)](./images/smilies/icon_e_smile.gif)
It will be interesting to see how much power it will run with sufficient linearity for DATV.
Dick G4BBH
Re: Motorola MHW2723
It's rated at 3W for Tetra which is DQPSK, so probably the same for us.
Postage to UK will probably be more, but it may not save much by getting a number of them and having to post them on from here.
Still no word from Cimko. I didn't think my French was that bad.
Brian
Postage to UK will probably be more, but it may not save much by getting a number of them and having to post them on from here.
Still no word from Cimko. I didn't think my French was that bad.
![Confused :?](./images/smilies/icon_e_confused.gif)
Brian
Re: Motorola MHW2723
I bought a couple and had a go at a DIY board - I managed to build the best wideband oscillator I've ever seen on my analyser!!
Talking to some folks in the know their comments were:
Important elements of the 'Test Fixture' are the use of capacitors having very low inductances. This is true for the 3.3uF - the ebay photo suggests it's a tant! Also L1 thru L4 are SMD inductors ( suggestion Farnell 2056515 - a Vishay-Dale product) and finally, build into the 'test fixture' 3 screens that separate the four inductors, and asociated components, from each other.
So yes, it is touchy and if there are some proven PCBs, I would definitely be interested in 2 units - maybe the BATC shop could do a bulk buy...
73s
Noel - G8GTZ
Talking to some folks in the know their comments were:
Important elements of the 'Test Fixture' are the use of capacitors having very low inductances. This is true for the 3.3uF - the ebay photo suggests it's a tant! Also L1 thru L4 are SMD inductors ( suggestion Farnell 2056515 - a Vishay-Dale product) and finally, build into the 'test fixture' 3 screens that separate the four inductors, and asociated components, from each other.
So yes, it is touchy and if there are some proven PCBs, I would definitely be interested in 2 units - maybe the BATC shop could do a bulk buy...
73s
Noel - G8GTZ
Re: Motorola MHW2723
I can confirm i'd be definitely be interested in two - esp if the batc shop was ordering some