This forum is run by the BATC (British Amateur Television Club), it is service made freely available to all interested parties, please do not abuse this privilege.
regards - Brett g6urm
its quite large - approx. 100 x 60 cm - but as i'm likely to be attempting longer and /or obstructed paths - owing to lack of activity down here - the more the merrier ...................
- gold-wireless-sad56030-5-ghz-wifi-directional-grid-antenna-outdoor-30dbi.jpg (84.99 KiB) Viewed 3785 times
Hello Brettg6urm wrote: ↑Sat Apr 28, 2018 11:56 am@ M0SKM - STEVE - um , so what prompted that decision for the mk2 ?? - cost - complexity - losses through the relay ?? - I ask because I WAS going looking for one at exter rally tomorrow - but may try and find another antenna instead if you think its a better way to go ................ thoughts please
regards - Brett g6urm
Initially I bolted a PA on the outside of MK1 as a test; there was no room for it inside.
Then a friend gifted me a nice big die-cast box to put it in. There are holes drilled in the bottom and top of the box and a fan on the PA.
When I started the MK2 build I decided to use 2 antenna's because there were fewer cables and connections and hopefully lower losses.
Hope your build all goes well and you find the bits you need.
Now what shall I do for MK3?
All the details are here http://www.5-6ghz-atv.co.uk/ in the hope that it might help those interested (but maybe put off by relays and the like) get one the air.
Hope it's of use to someone.
Regards and hope to 'see' you on 6cms!
Interesting link to the Line of Sight path plotting webpage - also now linked to on the wiki.
And congratulations on the NARSA award - well deserved.
Noel - G8GTZ
Looks like I have the same model myself, but a little scratched and bashed, before I was given it a few years ago.
I bolted a 2" Scaffold tube wall mount adaptor, the type you see on rugged hand rails, has Allen screw for swapping out stub poles.
Suspect yours might be similar.
This is the modification made for my tripod.
Caps on both ends of the tube are threaded and the 8mm threaded rod passes through the centre adding rigidity.
Replacing the stainless washer with nylon and the wingnut with a nyloc means you can set the right amount of friction for rotation.
1x sivers lab - PM-7552 C/O relay - good to about 18 GHz apparently - BRAND NEW IN ORG PACKING -£10
1 X RACAL - MESL - MICROWAVE CIRCULATOR - NG-3657 - anyone know anything about these ?? - only £2 so no loss if no good for project
2 x good to 1000 MHz c/o relays - £5 ea - used the same type on UHF before - so they are certainly good to that
2 - gotta be ex-mil 4 port c/o relays £0.50 p ea - no info - just the usual mod numbers painted on - but useful for parts maybe
and a V/A MODULATOR MODEL MTV 2500 - http://www.imajteknik.net/marka/bitel-microprogetti - THE ONE BOTTOM LEFT IN THE FIRST PHOTO - £ 3 - its marked freq B 401 - 405 ( mhz ???? ) - again may be of no immediate use but i have passed up obscure stuff in the past only to see an artical 6 months later using that very thing ................. and cursed myself for not getting it
anyhoo - the main thing is the first one - so if it works ok - yah boo sucks to the flea bay rip off merchants wanting £££££ s for the same thing
so there are useful bits out there if you look - the rest - well makes for good "junk box " items ..................... AND the sun shon for a change - BONUS