Source of potty parts
Forum rules
This forum is run by the BATC (British Amateur Television Club), it is service made freely available to all interested parties, please do not abuse this privilege.
Thank you
This forum is run by the BATC (British Amateur Television Club), it is service made freely available to all interested parties, please do not abuse this privilege.
Thank you
Source of potty parts
At the Newbury Rally I tried to find out where to obtain a potty for my dish. Apparently these are available from Holland. Does anyone have details please?
73 Nigel M0NDE
73 Nigel M0NDE
-
- Posts: 1236
- Joined: Wed Jan 06, 2016 9:46 am
Re: Source of potty parts
Try here https://www.passion-radio.com/satellite ... 20Es'hail2.
Or here...but he is out of stock, but with links to the original article etc.http://www.hybridpretender.nl/poty.html
Even with basic tools they are not that hard to make, its the patch that needs precision but hacksaw, file, step-drill and 4mm nuts as spacer when you solder the whole lot makes it simpler.
Gareth
Or here...but he is out of stock, but with links to the original article etc.http://www.hybridpretender.nl/poty.html
Even with basic tools they are not that hard to make, its the patch that needs precision but hacksaw, file, step-drill and 4mm nuts as spacer when you solder the whole lot makes it simpler.
Gareth
Re: Source of potty parts
Gareth,
Should that be 3mm nut for gap between plates.
Brian
Should that be 3mm nut for gap between plates.
Brian
-
- Posts: 1236
- Joined: Wed Jan 06, 2016 9:46 am
Re: Source of potty parts
Brian, no, the gap should be 3mm which (my) 4mm nuts conveniently are 'thickness-wise' ....
Gareth
Gareth
Re: Source of potty parts
Gareth,
had not realised a 4mm nut is 3mm thick
Brian
had not realised a 4mm nut is 3mm thick
Brian
Re: Source of potty parts
Nutters - M4 nuts are often 3mm thick, but measure it. The right gap is the most difficult bit.
There are some on Ebay but they are pricy. You could make your own, it isn't that hard, that was the point of the design, it could have been more complicated, with better performance, dual feed points, phasing lines, wider bandwidth, better circularity, but hard to make. I wanted to design a simple single point feed that almost anyone could replicate, a square piece of copper or brass with the corners cut off, a round bit and a length of 22mm copper water pipe. The compromise is the bandwidth, which is only a few percent, but if you are careful with the measurements, it should work, perhaps with a little bending. If you make the patch from copper it will be much easier to tweak by bending. With brass, you have to bend it more than required and hope it springs back to the right place.
Mike
There are some on Ebay but they are pricy. You could make your own, it isn't that hard, that was the point of the design, it could have been more complicated, with better performance, dual feed points, phasing lines, wider bandwidth, better circularity, but hard to make. I wanted to design a simple single point feed that almost anyone could replicate, a square piece of copper or brass with the corners cut off, a round bit and a length of 22mm copper water pipe. The compromise is the bandwidth, which is only a few percent, but if you are careful with the measurements, it should work, perhaps with a little bending. If you make the patch from copper it will be much easier to tweak by bending. With brass, you have to bend it more than required and hope it springs back to the right place.
Mike
Re: Source of potty parts
The metalwork on those AMSAT feeds is OK, but I have heard that the dielectric lens is not optimum for DATV use.
Dave, G8GKQ
Dave, G8GKQ
Re: Source of potty parts
Hi Dave.
Yes, people also buy the rocket lnb and take the lens off and use on poty.
Brian
Yes, people also buy the rocket lnb and take the lens off and use on poty.
Brian
- Attachments
-
- 20230610_132140.jpg (184.22 KiB) Viewed 6227 times
-
- 20230613_155051.jpg (134.04 KiB) Viewed 6227 times
Re: Source of potty parts
Ready built ones are now listed at the AMSAT-uk shop.
Only 4 left in stock at the moment though! https://shop.amsat-uk.org/product/poty
73
Graham G3VZV
Only 4 left in stock at the moment though! https://shop.amsat-uk.org/product/poty
73
Graham G3VZV