Minitiouner V1 is dead - Long live Knucker!

Discussion about the Knucker DVB-T Tuner DVB-T Receive Software. See also https://wiki.batc.org.uk/Knucker
Post Reply
g8lce
Posts: 340
Joined: Sun Dec 06, 2015 10:26 am

Minitiouner V1 is dead - Long live Knucker!

Post by g8lce » Fri Apr 02, 2021 11:04 am

As mentioned elsewhere in this forum you can convert the old Minitiouner V1 to a Knucker. Here is how I did it.

First see if your old Minitiouner V1 is working with a PC or Portsdown?
Now the final blow to it - cut out the old tuner so you can desolder the remains (no need if you used a socket)
Solder (socket) the new tuner from BATC shop (https://batc.org.uk/shop/serit-ftm-4762-nim/ ) leaving pins 3,5,6 and 7 bent away from the board. (or if you have sockets you have to alter the tracks )
Connect pins 5 and 6 to ground.
DSC00016.JPG
DSC00016.JPG (1.49 MiB) Viewed 5798 times


Now add 150k resistor in parallel with R5 (I used two to make up the value ).


DSC00006.JPG
DSC00006.JPG (1.06 MiB) Viewed 5798 times
Now all that is needed is to reprogram the USB device!
It took a while to work that out but it does work.

Here are some receiver photos..

DSC00010.JPG
DSC00010.JPG (1.48 MiB) Viewed 5798 times
DSC00011.JPG
DSC00011.JPG (1.49 MiB) Viewed 5798 times
DSC00012.JPG
DSC00012.JPG (1.53 MiB) Viewed 5798 times


Martin G8LCE

g8lce
Posts: 340
Joined: Sun Dec 06, 2015 10:26 am

Re: Minitiouner V1 is dead - Long live Knucker!

Post by g8lce » Fri Apr 02, 2021 12:05 pm

DSC00013.JPG
DSC00013.JPG (1.47 MiB) Viewed 5783 times
I could get it to work at 146.5MHz and 437MHz.
333kHz and 1000MHz with testcard and PiCam
I also used IPTS in as the encoder at 1000kHz Bandwidth and a 2000k stream input. This worked but with a very long delay (up to several minutes! Where does all that video get stored? )
Must get around to putting it a case this time...

Here is the modified Knucker with the old cut out tuner near a couple of Rydes:
DSC00007.JPG
DSC00007.JPG (742.54 KiB) Viewed 5773 times
Martin G8LCE

g8lce
Posts: 340
Joined: Sun Dec 06, 2015 10:26 am

Re: Minitiouner V1 is dead - Long live Knucker!

Post by g8lce » Sun Apr 04, 2021 9:31 am

For anyone trying to do this conversion here are some links:

Here you can find details of your old V1

https://wiki.batc.org.uk/MiniTiouner_hardware_Version_1

and here you can find details of the Knucker:

https://wiki.batc.org.uk/Knucker#Portsdown_system

From the two pages you can find the circuit diagrams and differences and also a guide to reprogramming the USB interface although more info is on this link:

viewtopic.php?t=4767

And finally here is the link to the inspiration for my experimentation:

viewtopic.php?f=134&t=7118&start=30#p26080

One other thing I found was that the USB would only program with power supplied to the board.

Martin G8LCE

G4GUO
Posts: 726
Joined: Tue Feb 16, 2010 12:51 pm

Re: Minitiouner V1 is dead - Long live Knucker!

Post by G4GUO » Sun Apr 04, 2021 11:29 am

Nice piece of upcycling :)

- Charles

Post Reply

Return to “The Knucker DVB-T Tuner and Receive Software”