ELAD Minitiouner

[G8GKQ]

Hi Rene

You can see the error messages by doing the following:

• Log on by ssh (username pi, password raspberry)
• Type menu and press enter (receiver stops, Menu appears in ssh terminal)
• Select "9 Utils"
• Select "6 Ryde Test"
• Ryde will run, and all the error messages will be displayed in the terminal window.
• Copy the error messages and paste them here for analysis.

Dave, G8GKQ

[g0mjw]

This is the Wiki page on programming the FTDI

https://wiki.batc.org.uk/MiniTiouner_ha ... USB_module

[DK1KIK]

Tank you Dave and g0mjw

here is the Output,

No MiniTiouner USB module found is the Problem I think, but why? its connected to the Pi4



pygame 1.9.4.post1
Hello from the pygame community. https://www.pygame.org/contribute.html
Namespace(conffile='/home/pi/ryde/config.yaml')
/home/pi/RydeHandsets/definitions
Warning: Watchdog file already exists, file will be reused
/home/pi/tmp/rydePlayer.pid
Player ID: Ryde
GPIO ID: 3
IF Freq: -0
Frequency: 1255000
Symbol Rate: 333, 333, 1000, 1200

--width 1920 --height 1080 --monitor-par 1:1 --mmal-display hdmi-2 --codec ffmpeg
[01b62980] vlcpulse audio output error: PulseAudio server connection failure: Connection refused
[01b5a950] vlcpulse audio output error: PulseAudio server connection failure: Connection refused
GPIO id: 3
Ready
Watchdog Starting: 0.1
State.Stopped
Watchdog Fired
Watchdog Starting: 0.2
State.Stopped
Watchdog Fired
Watchdog Starting: 0.4
State.Stopped
No MiniTiouner USB module found
No MiniTiouner USB module found
Watchdog Fired
Watchdog Starting: 0.8
State.Stopped
No MiniTiouner USB module found
State.Stopped
No MiniTiouner USB module found
Watchdog Fired
Watchdog Starting: 1.6
State.Stopped
No MiniTiouner USB module found
State.Stopped
State.Stopped
Watchdog Fired
Watchdog Starting: 3.2
State.Stopped
No MiniTiouner USB module found
State.Stopped
State.Stopped
State.Stopped
Watchdog Fired
Watchdog Starting: 6.4
State.Stopped
No MiniTiouner USB module found
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
Watchdog Fired
Watchdog Starting: 12.8
State.Stopped
State.Stopped
No MiniTiouner USB module found
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
Watchdog Fired
Watchdog Starting: 25.6
State.Stopped
No MiniTiouner USB module found
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
Watchdog Fired
Watchdog Starting: 51.2
State.Stopped
No MiniTiouner USB module found
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
State.Stopped
S

[DK1KIK]

Configuration Utility says

Modules:DA8KXP12 (1:3) : Unknown

[DK1KIK]

Hello,

ok, I think I solved the problem, I programmed the Tiouner with the "using NIMM Tuner" Template, The tuner is now recognized as a “minitiouner”.
Thanks to all
73
Rene