MiniTiouner V2.0 Contruction

Discussion about the MiniTiouner board and the MiniTiouner Digital ATV Receive Software. See also http://www.vivadatv.org/index.php
G4MJW
Posts: 30
Joined: Tue Jun 01, 2021 8:56 am

Re: MiniTiouner V2.0 Contruction

Post by G4MJW » Sat Mar 25, 2023 12:18 pm

Thanks Gareth, Brilliant.

Just waiting for 100n bigger lead spacing than I have in my drawer.could have used them but I ordered 50, so I'll wait a bit. Be nice to actually hear something on it (Langstone RX with Pluto is good).

Thanks again

Steve

User avatar
G3GJA
Posts: 338
Joined: Sun Nov 20, 2011 3:44 pm

Re: MiniTiouner V2.0 Contruction

Post by G3GJA » Sat Mar 25, 2023 12:39 pm

Just be aware that although the USB module is ready programmed, you do need to add a 10k resistor if you are going to use the later versions of the Minitioune software. Pin 10 of CN2 to ground as below.

10k.jpg
10k.jpg (391.09 KiB) Viewed 5538 times
Clive

G4MJW
Posts: 30
Joined: Tue Jun 01, 2021 8:56 am

Re: MiniTiouner V2.0 Contruction

Post by G4MJW » Sat Mar 25, 2023 12:53 pm

Thanks Clive . . . I did that this morning. Funny, I used a 10k (says 5.6k to 12k).

Watching, wating, hoping postman brings yo last capacitors today.

Thanks again.

Steve

sv1coasv1coa
Posts: 2
Joined: Sun Apr 02, 2023 4:52 pm

Re: MiniTiouner V2.0 Contruction

Post by sv1coasv1coa » Mon Apr 03, 2023 6:29 am

Hello i have one problem with my minitiouner v2 every time I turn on the my computer, the minitiouner drivers is gone, and I have to reinstall again, what happen? my system is win 10. :?: :?

G8DGR
Posts: 38
Joined: Tue Oct 01, 2013 3:06 pm

Re: MiniTiouner V2.0 Contruction

Post by G8DGR » Sat Mar 23, 2024 11:10 pm

Where did you get the PCB. The Shop says out of stock

radiogareth
Posts: 1236
Joined: Wed Jan 06, 2016 9:46 am

Re: MiniTiouner V2.0 Contruction

Post by radiogareth » Sun Mar 24, 2024 7:53 am

If you are stuck I have a blank spare I could post you, (and an FTDI module too) but its likely the shop stock will be in hand.
Gareth
Last edited by radiogareth on Sun Mar 24, 2024 9:25 am, edited 1 time in total.

g0mjw
Posts: 2350
Joined: Sat Sep 20, 2014 9:15 am

Re: MiniTiouner V2.0 Contruction

Post by g0mjw » Sun Mar 24, 2024 8:18 am

sv1coasv1coa wrote:
Mon Apr 03, 2023 6:29 am
Hello i have one problem with my minitiouner v2 every time I turn on the my computer, the minitiouner drivers is gone, and I have to reinstall again, what happen? my system is win 10. :?: :?
Which drivers? If you mean the USB then perhaps you have downloaded some other FTDI drivers that are conflicting? If you mean the graphics drivers perhaps they are corrupt or have a virus or something that the virus scanner thinks is a virus and are being removed or disabled.

Post Reply

Return to “The MiniTiouner and MiniTioune Digital Receive Software”